3v3
GND
1 37
2 36
3 35
4 34
5 33
6 32
7 31
8 30
Arduino
Mega
GPIO
5v
12v
>NAME
>VALUE
>NAME
>VALUE
DS1308
S8421-45R
>NAME
>VALUE
>NAME
>VALUE
>NAME
>VALUE
<b>Crystals and Crystal Resonators</b><p>
<author>Created by librarian@cadsoft.de</author>
<b>CRYSTAL</b>
>NAME
>VALUE
<b>Diodes</b><p>
Based on the following sources:
<ul>
<li>Motorola : www.onsemi.com
<li>Fairchild : www.fairchildsemi.com
<li>Philips : www.semiconductors.com
<li>Vishay : www.vishay.de
</ul>
<author>Created by librarian@cadsoft.de</author>
<b>Diode</b>
>NAME
>VALUE
<h1><a href="http://www.raspberrypi.org/">Raspberry Pi Board</a></h1>
<h2>Changelog</h2>
<ul>
<li>2014-01-25: Added RasPi Model B Rev 2</li>
<li>2012-01-29: Initial version from Jacques</li>
</ul>
<h2>Licence</h2>
This library stands under the <a href="http://www.ohwr.org/projects/cernohl/wiki">CERN Open Hardware Licence</a>.
<h2>Authors:</h2>
<a href="http://www.steffenvogel.de">Steffen Vogel</a><br>
<a href="http://www.raspberrypi.org/phpBB3/memberlist.php?mode=viewprofile&u=9306">Jacques Lagnel</a>
<h2>Links</h2>
<a href="http://www.raspberrypi.org/wp-content/uploads/2012/12/Raspberry-Pi-Mounting-Hole-Template.png">Mounting Holes</a><br>
<a href="http://elinux.org/RPi_Low-level_peripherals">GPIO Description</a><br>
<a href="http://openlab.com.au/wp-content/uploads/2013/04/Raspberry_Pi_Dimensions.png">Dimensions</a>
1
26
<b>AVR Devices</b><p>
ATmega640/1280/1281/2560/2561<p>
Based on the following sources:<p>
<ul>
<li>www.atmel.com
</ul>
<author>Revised by hendryczek@gmx.de</author>
<b>100-lead Thin Quad Flat Pack Package Outline</b>
>NAME
>VALUE
TQFP 100
R
<b>PIN HEADER</b>
>NAME
>VALUE
>NAME
>VALUE
<b>Pin Headers</b><p>
Naming:<p>
MA = male<p>
# contacts - # rows<p>
W = angled<p>
<author>Created by librarian@cadsoft.de</author>
<b>PIN HEADER</b>
>NAME
1
>VALUE
<b>PIN HEADER</b>
1
>NAME
>VALUE
8
<b>PIN HEADER</b>
>NAME
1
>VALUE
4
<b>PIN HEADER</b>
>NAME
1
8
>VALUE
<b>Voltage Regulators</b><p>
<author>Created by librarian@cadsoft.de</author>
<b>Small Outline Transistor</b><p>
TSC [Taiwan Semiconductor Company, Ltd]<br>
Source: http://www.taiwansemi.com .. 5205_0409c.pdf
>NAME
>VALUE
<h1>Jicamarca Library</h1>
<p>
<i>Creado por Jorge Ortiz, 2013.09.13</i>
<h2>Descripción</h2>
<p> Esta librerÃa de Eagle 5.9 incluye los diferentes dispositivos que se usan en todos los proyectos en Jicamarca, a excepción de los que estan incluÃdos por defecto en las librerias de instalación de Eagle.
<p> Uso: </p>
<p>Para añadir nuevos dispositivos, se puede abrir la librerÃa en eagle y añadir los dispositivos, sÃmbolo y/o paquetes correspondiente manualmente</p>
<p>Para añadir nuevos dispositivos desde otras librerÃas</p>
<ol>
<li>Bajarse la librarÃa correspondiente de Internet y abrirla en Eagle Control Panel</li>
<li>File > Export > Script (Creará un script con todas las partes de la librerÃa)</li>
<li>Script > lbrdump.ulp > [Script Exportado en paso anterior] (Creará un script por cada parte)</li>
<li>Añadir la librerÃa, el export, y las partes a SVN</li>
<li>Copiar solo las partes necesarias al directorio jocamarca_library/all_parts</li>
<li>Nota que algunos devices incluyen sus propios sÃmbolos y multiples paquetes, añadir esos también aun si no se usan.</li>
<li>Desde Eagle Control Panal, abror la librerÃa jicamarca.lbr</li>
<li>Hacer Run > Script > [Paquetes por importar]</li>
<li>Hacer Run > Script > [SÃmbolos por importar]</li>
<li>Hacer Run > Script > [Devices por importar]</li>
<li>Comprobar que los nuevos dispositivos estan en la librerÃa</li>
<li>Hacer Rename al device para ponerle un prefix adecuado (IC_, CONN_, RES_, etc..) y guardar los cambios</li>
<li>Hacer un commit en SVN a la nueva versión actualizada de la librerÃa</li>
</ol>
<p>
Scripts originales e instrucciones bajados de <a href="http://dangerousprototypes.com/docs/Dangerous_Prototypes_Cadsoft_Eagle_parts_library#Library_helper_scripts">Dangerous Prototypes</a>.
<b>CAPACITOR</b>
>NAME
>VALUE
>NAME
>VALUE
>NAME
>VALUE
FEMALE <b>SMA CONNECTOR</b><p>
Radiall<p>
>NAME
>VALUE
>NAME
UP1B
<b>RESISTOR</b>
>NAME
>VALUE
>NAME
>VALUE
<b>RESISTOR</b><p>
>NAME
>VALUE
<b>Coax Connectors</b><p>
Radiall and M/A COM.<p>
<author>Created by librarian@cadsoft.de</author>
FEMALE <b>SMB CONNECTOR</b><p>
Radiall<p>
distributor RS 112-2993
>NAME
>VALUE
<b>EAGLE Design Rules</b>
<p>
Die Standard-Design-Rules sind so gewählt, dass sie für
die meisten Anwendungen passen. Sollte ihre Platine
besondere Anforderungen haben, treffen Sie die erforderlichen
Einstellungen hier und speichern die Design Rules unter
einem neuen Namen ab.
<b>EAGLE Design Rules</b>
<p>
The default Design Rules have been set to cover
a wide range of applications. Your particular design
may have different requirements, so please make the
necessary adjustments and save your customized
design rules under a new name.
Since Version 6.2.2 text objects can contain more than one line,
which will not be processed correctly with this version.